TOOLS, CARTRIDGES & MOLDS
| FC-Tool 61 | Musket tool, open end nipple wrench | $12.50 | Copy of 1861-1864 musket tool / 2 blade screwdriver |
|---|---|---|---|
| FC-Tool 55 | Musket tool, open end nipple wrench | $12.50 | Copy of 1855 pattern tool with nipple wrench and 3 blades |
| FC-Tool 42 | Musket tool / closed nipple wrench | $12.50 | Copy 1842 musket tool with closed nipple wrench & 2 blades |
| ES-GALL | Gallagher nipple wrench and cartridge puller | $40.00 | Copy of original Gallagher tool, well made |
| ES-MAY | Maynard nipple wrench, copy of original | $40.00 | closed box, tapered to fit easily under the hammer |
| ES-SHP | Sharps nipple wrench, copy of original | $40.00 | exact copy of original, closed box |
| ORIG-tool | Musket tool, nipple wrench 1861-64 | $65.00 | Orig. Springfield 1861 musket tool, nipple wrench & screwdrivers |
| AC THW | Nipple wrench, T handle w/ nipple pick in the top | $20.00 | Fits square sided nipple bases, Italian, may be a bit loose on original nipple. |
| AA THW | Nipple wrench, T handle Short block will fit Maynard and all 1/4" nipple base | $9.95 | Fits square sided nipple bases 1/4" some Italian mfg. are too large, Pictured on front page |
| SS-SW61 | Sight wrench for original rear sight base screw, 1855-1863 | $ 10.00 | Fits Orig. Springfld screw & older pre 1999 Euroarms '61 |
| AC220-SW | Sight wrench for repro 1861 Springfield rear sight base screw | $15.00 | Italian Repro fits Armisport & new Euroarms 1861 |
| OUS-BP | Band Spring punch | $12.00 | Original |
| OUS-SP | Stirrup pin punch | $20.00 | Original punch |
| AC220-MV | Mainspring clamp Springfield 1861 style | $25.00 | Reproduction |
| OSP-MV-US | Mainspring clamp Springfield, marked US | $75.00 | Original clamp |
| LIB-30C | PATCHES, cotton flannel to Military specs | $ 4.50 | Package 200 / 2.5" works for .54, .58, and .69 cal muskets |
| LIB-30C-SL | PATCHES, cotton flannel to Military specs | $22.50 | SLEEVE OF 5 PKGS....2.5" works for .54, .58, and .69 cal muskets |
| Powder Flask, Zouave | $32.00 | Italian Repro/ musket style 60 gr spout | |
| Powder Flask, Remington Pistol style | $28.00 | Italian Repro | |
| Powder Flask, Colt Pistol Style | $28.00 | Italian Repro | |
| Replacement spout for above flasks | $ 4.00 | 30gr to 120 grain sizes available | |
| Sight protectors for pistol | $11.00 | avail in several sizes- please state model (ie Colt,Rem). | |
| Stadia | Stadia range finder, copy of original (used as an award for fine markemanship 1862-88) OUT OF STOCK | $85.00 | brass, 2 sided, cavalry and infantry distance finder |
| BULLET MOLDS by LEE limited quantities ---- inquire before ordering | |||
| part # 515x2 | Smith / Maynard bullet cast 2 at a time LEE aluminum mold bullet .515 350 gr. OUT of STOCK | $42.00 | 2 cavity mold with handles, 3 grease groves 350 grain bullet |
| part # 515x6 | Smith/ Maynard bullet 6 cavity mold | $75.00 | 6 cavity mold same bullet as above only 3 times as fast uses commercial /HANDLES sold seperately |
| part # 518x2 | Smith / Maynard bullet cast 2 at a time LEE aluminum mold bullet .518 350 gr. | $42.00 | 2 cavity mold with handles, 3 grease groves 350 grain bullet |
| part # 518x6 | Smith/ Maynard bullet 6 cavity mold | $75.00 | 6 cavity mold same bullet as above only 3 times as fast uses commercial /HANDLES sold seperately |
| Commercial | MOLD HANDLES for 6 cavity LEE mold fit most smaller molds and keep you futher from the heat. | $22.00 | Handles by LEE for 6 cavity commercial and other large molds, will fit Lyman and Rapine molds |
| size 577-1 | Ash can single cavity aluminum mold by LEE | $33.00 | single cavity aluminum mold with handles size .577 NEW |
| size 578-1 | Old Style Mini single cavity aluminum mold by LEE | $33.00 | single cavity aluminum mold with handles, size .578 NEW |
| size .575-1 | Old Style Mni single cavity aluminum mold by LEE | $33.00 | single cavity aluminum mold with handles, size .575 NEW |
| We have a grab bag of Rapine and Lyman used molds | inquire for sizes | ||
| size 678-1 | Round ball mold / Lyman single cavity .678 steel mold | $99.00 | single round ball mold , new in box Lyman |
| size 576 | Hodgden .576 single cavity mold | $98.00 | single cavity mold, deep grease groves, 350 grain / shooters favorite |
| size .578 | Hodgden .578 single cavity mold | $98.00 | single cavity mold, deep grease groves, 350 grain / shooters favorite |
| AA-PD | Sizing die, push thru design | $18.00 | can be mounted to a wood stand or hand held, available sizes same as below plus .678, .679, .680, .685, and .689 |
| KV-577 | Sizing dies to fit LYMAN or RCBS Lubrisizer | $33.00 | avail. in 1/1000 variants from .360 to .802 see picture includes top punch please specify flat or concave with your size needed IN stock .404, .424, .429, .430, .512 thru .520, .533, .534, .536, .537, and .572 thru 582 |
| GPS lube | Bullet lube / generic SPG lube in 6 oz cup | $ 3.00 | looks like SPG and works like it too. Good feed back from trials. |
| Pete | BULLET LUBE / Pete's Lube 8 0z cup ---------- out of stock 11/15/11 | $4.50 | Van Dexters special formula, created in the 1960's, tried and true, works great even in cold weather. |
| Lee/alx | Alox, liquid bullet lubricant------------------ out of stock 11/15/11 | $5.00 | 4 oz size packaged by Lee Precision |
| Lee/Al-wx | Lee NRA Formula bullet lube stick form | $5.00 | Alox and beeswax stick to fit lubrisizers by Lee Precision |
| The list goes on . . . . . . . | $ .00 | ||
| CARTRIDGE CASES, CARBINE AND MUSKET QUICK LOADS | |||
| BURNSIDE brass cartridge case / concave bottom | $4.00 | $395.00 per 100 | |
| 50 Cal | MAYNARD brass cartridge / full capacity | $ 2.25 | aprox. 40 grains $220.00 per 100 |
| 50 Cal | MAYNARD brass cartridge / reduced capacity | $ 2.25 | aprox. 30 grains $220.00 per 100 |
| 35 Cal | MAYNARD brass cartridge / for 1st Model | $2.50 | $238.00 per 100 or more |
| 50 Cal | MAYNARD plastic cartridge / full capacity | $ .37 | $34.00 per 100 |
| JH/MY | MAYNARD bullet seating tool | $40.00 | steel tube and punch allow you to seat your bullet to the same depth every time |
| 50 Cal | SMITH brass cartridge | $ 2.25 | $220.00 per 100 or more |
| 50 Cal | SMITH black plastic (highly heat resistant) | $ .37 | $34.00 per 100 or more |
| JH/SM | SMITH bullet seating tool, steel | $40.00 | like Maynard in style, steel tube with top punch for loading consistency |
| ES/SM | SMITH bullet seater, brass in original pattern | $35.00 | brass w/ base stand for cartridge ...... see picture |
| 52 Cal | GALLAGHER brass cartridge/ accepts both the original style Gallagher bullet and the 50 cal Maynard minie ball for those barrels that have been sleeved to .515 | $ 2.25 | $220.00 per 100 or more |
| 56-50 | SPENCER cartridges/ brass .56-50 | $ 2.25 | custom new made to fit original .56-50 |
| 56-50 | SPENCER cartridges mfg Starline .56-50 bag of 50 | $78.00 | mfg to fit the Armisport repro detail below |
| 56-50 Spencer brass from Starline - Was built to C.I.P. specifications for operation in the Taylor Arms .56-50 Spencer. Rim diameter = .629 to .632, which may be too small to eject properly in some originals. Rim thickness = .057 to .061. Thickness of wall at mouth is .0125 average. Primer pocket is designed for large rifle primer. Case mouth may need to be annealed if not sealing properly. Maximum bullet seating depth = .375. | |||
| .54 Cal | Quick load tube, soft cap, round bottom .531x1.5" | $ .37 | Color, currently avail. in black $34.00 per 100 |
| .58 Cal | Quick load tube, cap plug, flat bottom / thicker than avg. w/ larger capacity to use for hunting loads also | $ .28 | Colors avail. dk red, purple and dk yellow $26.00 per 100 |
| .69 Cal | Quick load tube, soft cap, round bottom .687x1.5" | $ .37 | Color, currently avail. in RED $34.00 per 100 |
| .72 Cal | Quick load tube, for .72 round ball soft cap, round bottom .715 x 1.5" | $.37 | Color currently avail. in black $34.00 per 100 |
| PISTOL ACCESSORIES | |||
| .36 & .44 cal | Quick load tubes, soft cap, round bottom .437 x 1.5" | $ .37 | $34.00 per 100 .44 cal. in blue and .36 cal in black |
| Pistol | Oak Loading Stand / holds '58 Remington and Colt 60 & Colt 1851 Navy | $15.00 | Perfect loading accessory for competition shooting |
| Pistol | Cleaning rod, double ended one for barrel other for cylinder | $24.00 | brass rod and attachments .36 or .44 cal |
| KV-435 | Sizing dies to fit LYMAN or RCBS Lubrisizer | $33.00 | avail. in 1/1000 variants from .360 to .802 see picture includes top punch specify flat or concave |
| Pistol | Straight line capper | $10.00 | Makes capping the pistol so much easier |
| Pistol | Caps #10 RWS....... CAPS we do not ship caps; Hazard Material shipping would be $25.00 | $ 12.50 | Tin of 100 |
Order Form ---------------Return to Index ----------------Return to Front Page
Lodgewood Mfg., PO Box 611 Whitewater, WI 53190-0611 .. email Lodgewd@idcnet.com .. phone 262-473-5444 .. FAX 262-473-6448
